I can connect to my Raspberry Pi via SSH.
I can deploy an app to a Raspberry Pi.
I can compose a higher-ordered algorithm.
I can update code on my Raspberry Pi.
I can make short, descriptive commit messages.
You will submit a link to your GitHub repo.
You will demonstrate your capacity to control your robot.
You will be asked regular comprehension questions about Raspberry Pis.
This is a PCB with all the basic components found in a personal computer (PC)
Visit the project and fork it
Open Replit and start a new project from github
Use your forked github project. You should now see your code on your editor. Explore student.py and teacher.py.
Use SSH (on Mac) or PuTTy (on Windows) to connect to your robot. Install PuTTy if it is not on your computer.
Open putty and enter the ip address of your robot. Click open.
login: pi
password: robots1234
Remove the Piggy folder if it's already there: rm -rf Piggy
Now we'll clone your project on the robot too with git clone https://github.com/YOURUSERNAME/Piggy
Change to your project folder: cd Piggy
Run the app: python3 student.py
Whenyou make changes to your app and want to update the code on your robot, we first need to send the code from our computers to GitHub. This happens in the version control tab by typing in "What did you change" and hitting Commit & Push.
Now we'll remote control our robots using SSH. We'll use Linux commands to pull the updated code down from GitHub.
Open putty and enter the ip address of your robot. Click open.
login: pi
password: robots1234
Note: You will not see the password when typing. This is a security feature!
Make sure you're in the right folder: cd Piggy
Pull your updated code: git pull origin master
Run your app: python3 student.py
If it doesn't run, study the error.
We'll need to configure your class variables.
If the servo wasn't mounted perfectly, the midpoint won't be 1500. But that's rarely the case. We should adjust this magic number to fit your particular robot.
Sometimes one motor will perform faster than the other, giving the robot a noticeable veer. We can try to correct for this drift by adjusting the motor power.
Check out what commands are available from the API that's provided for you. These are the commands you're inheriting.
Your dance method should read as close to regular English as possible. The nitty-gritty commands are all kept in the particular methods being called in your dance algorithm. So your dance method should just call a handful of moves. Within those moves, you'll use the specific motor commands below and get into the nitty-gritty of robot control.
deg_fwd(angle) - how many degrees do you want your wheels to rotate? You need to pass the angle
turn_to_deg(angle) - rotates to the given angle as calculated by the piggy's gyroscope
turn_by_deg(angle) - turns relative to it's current heading. Positive values rotate right and negative rotate left
fwd - powers on your robot to drive forward. You'll need to use self.stop() to power off the motors
right - by default, self.right() will give the left motor 90% power and the right 0% which rotates right. You can use kwargs to adjust the power such as self.right(primary=90, counter=-90), which will spin the robot in place
left - same as right but reversed.
back - same as fwd but in reverse.
servo - moves the servo (plugged into servo1) to the given value (use 1000 - 2000)
stop - sets motor power to zero
read_distance - returns the distance from the distance sensor (plugged into I2C port) in millimeters
get_heading - returns the gyroscope's value
To shut down your robot, type: sudo shutdown now in the putty window.
Square
Dance
Add safe_to_dance() method which checks surroundings and only dances if it has enough space.
Move to wall and stop
Move to wall and turn around. Move forward again and repeat endlessly.
Move to box and go around it
Before moving around box, figure out which side of closer. If you are closer to the left end of the box, go around left. If you are closer to the right end of the box, go around to the right.
Write a move method which scans slightly to the left and right of the robot as it moves forward.
If it senses a wall straight ahead, it goes around to the closest side as above (put that move in it's own method)
If it senses a wall at the edges of the robot, swerve slightly to miss the wall (this swerve should again be in it's own method).
Coming soon.
